Products > Omniterm > Special Functions

OMNITERM SPECIAL FUNCTION MODULES

The Omniterm Special Function modules include a computation module for those odd tricky special calculations required from time to time, a compatible AC power module to assist in applications where no 24Vdc is available, and a range of Modbus interface modules for data acquisition.
Back to the Omniterm Signal Conditioning Overview

Omniterm TFX
Model C2404B
DIN rail mount maths computation module

Use the TFX to perform specialised analogue computation on 4-20mA or 1-5Vdc instrument signals. This instrument has two inputs and an isolated output, performing a variety of easily selectable preset functions. The inclusion of a 32 point breakpoint linearisation table adds the ability to linearise any signal.

Omniterm PAF
Model C2440A
DIN rail mount  85-264Vac Power Supply

Use the PAF power supply to power a system of Omniterm modules when 24Vdc power is not available. Compact design mechanically compatible with the other Omniterm modules provides a convenient and space efficient implementation of high voltage ac powered systems. Reduce the chances of hazards from high voltage by keeping the individual instruments in the panel at safe 24Vd voltages. 

Omniterm TFX Maths Computation Module

All digital design means higher accuracy calculations over the full range.

Over 12 built-in common maths functions make setup quick and easy.

Bipolar isolated current or voltage, or pulse outputs means widest range of applications.

All settings user configurable allowing only one type to be kept on the shelf.

see more information...

Omniterm PAF AC Power Supply

User configurable to any input range minimises strategic stock holding.

No field calibration required means lowest installation and commissioning costs.

Fully isolated input for reliable operation.

Software configuration means range setting can be done in minutes using the free software, and configuration can be stored for effective asset management.

see more information...

Omniterm MIR
Model C2302C
DIN rail mount Modbus 16 channel Digital input module (with Omniflex standard ribbon header termination).

Use the MIR module as a general purpose digital input module on any Modbus ASCII or RTU RS232/485 network. Input termination is by 20 way ribbon cable header compatible with many Omniflex products such as the Omni16 alarm annunciators.

Omniterm MIT
Model C2303C
DIN rail mount Modbus 16 channel Digital input module (with screw terminal inputs).

Use the MIT module as a general purpose digital input module on any Modbus ASCII or RTU RS232/485 network. input termination is by screw terminals allowing any general purpose digital inputs to be monitored.

Omniterm MIR 16ch Modbus Digital Input Module (Ribbon Header))

Simple DIP switch settings for Modbus Slave operation provides ultimate simplicity.

Fully isolated RS232/485 communications gives best noise immunity.

Compatible with Omni16 alarm annunciator repeat outputs and other Omniflex products.

Multi drop up to 32 units to a single Modbus Master.

see more information...

Omniterm MIT 16ch Modbus Digital Input Module (Screw Terminals)

Simple DIP switch settings for Modbus Slave operation provides ultimate simplicity.

Fully isolated RS232/485 communications gives best noise immunity.

Modbus Master Mode available to communicate with other Modbus slaves.

see more information...

Omniterm MOR
Model C2304C
DIN rail mount Modbus 16 channel Digital Output module (with Omniflex standard ribbon header termination).

Use the MOR module as a general purpose digital output module on any Modbus ASCII or RTU RS232/485 network. Output termination is by 20 way ribbon cable header compatible with many Omniflex products such as the Omni16 alarm annunciators.

Omniterm MOT
Model C2305C
DIN rail mount Modbus 16 channel Digital Output module (with screw terminal inputs).

Use the MOT module as a general purpose digital output module on any Modbus ASCII or RTU RS232/485 network. Output termination is by screw terminals allowing any general purpose digital outputs to be controlled.

Omniterm MIR 16ch Modbus Digital Input Module (Ribbon Header))

Simple DIP switch settings for Modbus Slave operation provides ultimate simplicity.

Fully isolated RS232/485 communications gives best noise immunity.

Compatible with Omni16 alarm annunciator ribbon header inputs and other Omniflex products.

Multi drop up to 32 units to a single Modbus Master.

see more information...

Omniterm MIT 16ch Modbus Digital Input Module (Screw Terminals)

Simple DIP switch settings for Modbus Slave operation provides ultimate simplicity.

Fully isolated RS232/485 communications gives best noise immunity.

Modbus Master Mode available to communicate with other Modbus slaves.

see more information...

See our range of compatible Alarm Annunciators...